How to lace ankle boots

Berts are an exceptionally comfortable type of footwear that can be used both in autumn and winter. The relatively light weight of these shoes is another advantage that is almost impossible to offset by anything. These shoes can be called both stylish and extremely practical. It will be an ideal choice for those who would like to purchase the most versatile wardrobe item possible.

However, ankle boots have one drawback. Over time, this shortcoming may not be noticed, however, to do this you will have to master a relatively complex skill. The point is that lacing up ankle boots takes a long time, and most importantly, it’s difficult. It will be extremely difficult for an unprepared person to cope with this task. This is precisely why it is so important to master this skill as soon as possible. In this case, such shoes will be the ideal solution for any time of year.

Why lacing boots is so important

There are many reasons for lacing boots correctly.

• If you do not pay attention to lacing, wearing shoes will be extremely uncomfortable. The fact is that laces are an extremely important attribute of this type of shoe, so it is simply impossible to do without them. This is the same as trying to drive a car whose tank is completely empty.
• The situation is similar with ankle boots, because standard lacing will not help here. With its help, it will not be possible to secure the ankle boots as needed.
• Moreover, insufficient quality lacing can also cause numerous problems. In particular, if these shoes are poorly secured to the foot, then if you fall, you can get serious injury.
• This is not the worst thing, because poor lacing is the cause of blood supply problems. This problem should concern even young people, because otherwise, after a couple of years, serious difficulties may arise while walking.

How to choose the correct length of laces for combat boots

Finding the most suitable length of laces can be an overwhelming task for the vast majority of people who are buying such shoes for the first time.

• It is recommended that you choose your laces with someone who has done this before. Someone else's experience in this case will come in handy. In addition, the best option would be to try to study the length of the old laces. If such an opportunity is not available at all, then you will have to rely on the opinion of the consultant of the store where the ankle boots were purchased. He must have such information.
• Despite the fact that there is a lot of information on this subject on the Internet, it is best to trust people who have already worn such shoes. They will be able to give much more valuable advice.

IMPORTANT! The total length of laces that may be required for such shoes directly depends on the number of holes.Most often, on the Internet, you can find information that in the case of two pairs of eyelets, you will need laces whose length reaches 45 cm. If we are talking about 3-4 pairs of holes, then you will need laces 60 cm long, and so on.

What material should laces for ankle boots be made of?

Today, laces are made from a variety of materials, including leather, jute, and cotton. When choosing laces, you need to focus on your own needs. It is possible that the buyer of such products is a purely domestic person who does not need any additional advantages of materials that can withstand extreme operating conditions. In this case, it is recommended to choose laces that have a stylish and modern appearance.

Schemes on how to lace up special forces boots

The lacing process in this case is quite simple. First you need to thread a couple of ends into the holes that are located on the bottom of the shoe. After this, all that remains is to insert the ends of the laces into the eyelets. They are located opposite. This completes the lacing process.

Army-style lacing of ankle boots

The most popular type of lacing is military. There are many reasons for this. In particular, this way you can tie your shoelaces as quickly as possible.

1. First you need to thread the laces through a couple of holes located at the bottom.
2. After this, you need to cross the ends, and then thread them into another row of loops. Since in this case it is speed that is important, then, obviously, at the first opportunity you need to tie your laces in any other way.

This method was developed specifically for those who need speed. This type of lacing is called “military” for a reason. With its help, a soldier will be able to put on his shoes in just a few seconds, after which he will be absolutely ready to perform any combat mission.That is why this type of lacing is called military.

Quick lacing of ankle boots

This option is suitable both for emergencies and for those people who simply like to save time.

1. The first thing to do is tie as tight a knot as possible at one end of the lace. After this, you need to insert the end into the bottom hole from the outside of the shoe. In the boot itself for the right leg you will have to thread the lace into the lowest hole located on the right.
2. Then you need to pull the lace to the end, and the knot should be inside.
3. Now you need to remove the lace from the top of the strip, and then thread it through the grommet located on the opposite side. The end of the lace must be threaded into the hole located at the top. Then the free edge should be brought out. All that remains is to thread the cord into the hole opposite and stretch it along the inside to the next eyelet.

Attention! At the very last hole, you need to insert the lace inside the grommet from the outside, and then immediately pull it back out, making a loop using this method. You can thread the free end into it. Then the knot is tightened in the very middle.

Lacing ladder

Also today, ladder lacing is very popular. It also has another name – “European”. Shoes that have been laced this way look very neat. To do this, you just need to pass 1 lace through the holes that are located below. After this, all that remains is to bring the lace out from all ends.

Even a schoolchild can cope with this task, which is why the “ladder” lacing method is quite often practiced in camps for teenagers. There, children are taught a wide variety of skills that can be useful to them in real life.One of these skills is the ability to tie ankle boots. The “ladder” method can be called ingenious, because in this way you can not only save a lot of time and effort, but also effectively tie the laces on your own shoes.

How to make hidden lacing of ankle boots

If we are talking about rough terrain or some other difficult conditions, then it is best to lace up the boots in a different way than always. In this case, the laces will not cling to grass, snags, and branches. What needs to be done to realize all your plans? First you need to thread the ends of the laces through the lowest holes. When this is done, all that remains is to tuck one of them into the next one, which is all on the same side. Then you need to change sides and continue lacing in the same way.

Boots as an element of a fashionable look

Recently, ankle boots have become increasingly popular. They go with a variety of things, so they can be used in almost any wardrobe.

INTERESTING FACT. Most often, combat boots are needed to emphasize the masculinity of a suit. Interestingly, girls often use this element.

They will make their owner much more attractive in the eyes of women, because such shoes even go with jeans and look very masculine. Typically, buyers prefer those models that have universal colors. In this case, you can wear these shoes at almost any time of the year, except autumn.

How to tie ankle boots beautifully

This method is extremely simple.

1. First you need to take the lace and try to pull it through literally all the holes that are located at the bottom of the shoe.
2. After this, the ends need to be crossed together and threaded into other holes (we are talking about the upper part of the shoe).Then you will get a stylish lacing that will highlight all the advantages of this shoe.

Where to put the rest of the laces

Many people believe that the easiest way is to use the last hole in the row. Then you just need to insert the ends of the laces inward, not outward. In this case, after the laces are tied, the ends of the bow will be positioned so that they can be threaded through the “tongue”.