Humanity has been trying to cover windows from prying eyes and sunlight since ancient times. Previously, curtains were used for this, but now blinds are becoming increasingly popular. The slats in them can be either horizontal or vertical.
Horizontal blinds are divided into different types: attic, roller, bamboo shutters, etc. Such devices have different functioning mechanisms and dimensions.
They are attached to the frames; they can be installed on top of the window block or inside the frames. It all depends on the wishes of the apartment owner and the dimensions of the window opening. Most often, such structures are installed in offices, houses, apartments, factories, retail outlets, and shops. Their color palette is very rich.
We attach horizontal blinds to plastic windows
The product can be attached to the profile of plastic windows in two ways:
- Using self-tapping screws. This method involves drilling. Disadvantage: after dismantling it is difficult to remove the remaining holes from the fasteners.
- No drilling. In this case, the entire structure is less stable, but the appearance of the window does not deteriorate.
Self-tapping screws
In order to install blinds on a plastic window we will need:
- Screwdriver (screwdriver).
- Slats (for each sash).
- Pencil.
- A little time and patience.
- Bottom fasteners (2 pieces per sash).
- Upper fasteners (2 pieces per sash).
- Self-tapping screws (4 per sash).
Work progress
- Unpacking, we unwind the cord for adjustment.
- We remove the adjusting bar.
- We need to put a bracket on the top of the product.
- We make a measurement. To apply markings, it is recommended to apply a spirit level so that the top plate is strictly horizontal and does not fall to the side or down. If the window itself is installed with a skew, then the installation is done based on this skew of the sashes.
- We put a mark where the self-tapping screw will be screwed in.
- We check the correctness of the marks.
- Let's try it on again and remove the brackets.
- We take the right bracket, apply it to the intended area and screw it in with a screwdriver.
- We install the second bracket in the same way.
- We put on the blinds and open them.
- We place clamps on the sides of the canvas.
- Let's check if the mechanism works.
To clean, snap off the bottom slats and pull the blinds upward. We wipe the window and put the slats in place. The dust is swept away with a broom; after cleaning, an antistatic aerosol should be treated so that the structure collects less dust.
Fastening without screws
Typically, such fasteners are used in rented areas, when the appearance of the windows cannot be spoiled.
We will need:
- Scissors.
- Double-sided tape.
- Set of blinds.
- Pencil.
Work progress
- Unpack the package.
- We remove the adjustment bar so that it does not interfere.
- Place the block with the wrong side up.
- We measure the length of the tape equal to the length of the body.
- Cut off the excess tape.
- We remove the protective strip and stick it on the wrong side of the block.
- We try on the location of the blinds relative to the window sashes.
- We mark the points where the ends of the blinds will be attached.
- Remove the protective strip and glue the top part.
- We press the profile well to the surface.
- We install the adjustment bar.
- We check the operation of the structure.
Important! The width of the tape should be approximately equal to the width of the block. We smooth out the tape so that there are no blisters; it should lie evenly over the entire surface.
We attach horizontal blinds to wooden windows
We take measurements
We measure the dimensions, taking into account the size of the window. When installing in an opening, subtract 1 to 2 centimeters. This is a correction for uneven slopes. After this, we determine where the controls will be located (left or right side). After this, you need to decide on the type of brackets that will be used (standard; twist model). We measure the length of the handle to control the structure; usually its standard size occupies 2/3 of the entire height of the product.
Important! The maximum width of the lamellas is about 22 centimeters. There are also larger sizes in stores, but with a width of, for example, 30 cm, no one can guarantee that the blinds will open and close well. The recommended maximum height of the structure should be no more than 2.5 meters.
How to attach horizontal blinds to look like wood
This is a design with lamellas made of aluminum, which imitates natural wood due to polymer coloring. It is perfect for complementing a classic interior.In appearance they look like wood, but are less capricious and easy to use.
It is recommended to install such blinds on twist brackets. We will need a set of blinds, twist brackets, and a pencil.
- We make outlines with a pencil in the places where the brackets will be installed. There should be at least 60 centimeters between them.
- Please note that the brackets should not interfere with the assembly of the blinds or get into the latch or other moving parts of the mechanism.
- We attach them to the sash, wall or ceiling (depending on the owner’s preferences).
- Turn the latches counterclockwise until they click.
- We place the upper part in the fasteners and screw the latches until they stop, turning them clockwise.
- We check the operation of the entire structure.
How to attach horizontal beech blinds
What you will need for installation:
- Phillips screwdriver.
- Level.
- Felt pen.
- Pliers.
- Knife.
- Roulette.
- Hammer.
We take measurements and markings
It is necessary to pay attention that after installation the product should not block the access to the window handle and should not interfere with closing and opening it. We outline places for installing brackets. One of the upper mounts should be located next to the mechanism. Because when folding and unfolding, a large load is placed on this place and it is easy to break the fastening.
Mark the required points with a marker. Self-tapping screws should not be taken more than 1 cm, otherwise there is a high probability of damage to the glass unit, which will lead to its depressurization. Because of this, constant condensation will begin, which will disable the window opening mechanism.
Mounting on inclined windows
- We install twist brackets on the top of the window.
- Plastic brackets are installed on the bottom.
- We fasten the cables to the bushings.
- We put bushings in the holes in the upper cornice.
- Install cornice on brackets.
- We pass the cable through the holes at the edges of the planks.
- We put the second set of bushings in the holes in the lower brackets. We pass the cable through it and fix it with a screw at the top.
- We fix the window handle.
- We check the operation of the entire mechanism.
Differences between horizontal and roller blinds installation
Rolled - this is a single canvas wound into a roller. Such a canvas is usually fixed above the window, and the lower edge of the product is equipped with a special rail to make the structure heavier. This is an open type product. They are recommended to be installed above the window.
The closed type design consists of a box with a roller closure and side dies that help fix the canvas to the window. They are often equipped with electric drives, which operate from a control panel. This system makes such structures more comfortable to use.
While horizontal blinds are attached to the wall, to the ceiling, they can be installed between frames (mainly used for wooden windows).
Conclusion
Horizontal blinds are a universal way to enhance a window opening. Due to the variety of materials and colors, they are used for installation in apartments, private houses, offices, and retail outlets. Installation methods are easy to select depending on the owner’s wishes: outside, inside the opening, on the window frame, between the frames.
The most important advantage is that almost anyone with a minimal set of tools can install such a mechanism. (screwdriver, screwdriver, knife, hammer), a little patience and skill. Blinds do not block light sources completely, but help create diffused lighting.
0
