Do-it-yourself computer chair reupholstery: how to sew a cover, ideas

prom.ua

Any armchair or computer chair loses its appearance over time. They do not become less comfortable, so not everyone decides to part with their favorite chair because of the unsightly appearance of the upholstery. In this case, the question arises: how to reupholster a computer chair with your own hands? In fact, the procedure does not take much time and effort. There must be certain tools and materials available. Before upholstering a computer chair with your own hands, you need to select the fabric. It is more difficult to work with leather upholstery, so it is easier to choose a special fabric for furniture.

How to reupholster a computer chair with your own hands

Reupholstering a computer chair with your own hands begins with removing the old material. Furniture restoration consists of several steps:

• Using tools, remove the backrest. To detach the armrests, you need to turn the rear screw. Remove the back panel of the product.
• To reupholster a computer chair, remove the old fabric. To do this, you need to turn the chair upside down and free it from the upholstery on the seat.
• We will place a piece of foam rubber under the seat and cut it to fit the dimensions of the chair.
• To secure soft material, we use special staples. They can be found at any hardware store.
• The new fabric needs to be stretched and secured to the back of the seat. Treat the back in the same way.
• Given the soft contours of the computer chair, it is important to carefully control how the material lays. Upholstering an office chair with your own hands should be done carefully so that folds and gathers do not appear on the canvas.
• We cut off excess pieces of material with scissors or a knife.
• Assembling a computer chair. Now it looks like new.

How to sew a cover for a computer chair

prom.ua

If it is not clear how to reupholster a computer chair, you can simply sew an office chair with your own hands. To do this you will need to prepare:

1. One and a half meters of linen elastic.
2. Threads of a suitable color.
3. Seventy centimeters of gabardine.
4. Sewing kit: tape measure, scissors, chalk, pins.

To make a cover for a computer chair with your own hands, it is better to choose durable fabric that is not easily soiled and is pleasant to the body. Wool or satin will not work. Therefore, we will focus on gabardine. It is wear-resistant, comfortable and can be easily washed from dust and stains. How to cover a computer chair:

• We measure the seat with a centimeter.
• Use chalk to cut out the future cover on the wrong side of the material. We take into account an allowance of nine centimeters on all sides.
• To make a beautiful cover for a computer chair with your own hands, you need to slightly round the corners when cutting out the pattern.
• We sew along the edges of the product. You can use an overlocker or a zigzag stitch on a machine.
• On the wrong side, we bend the material along the edges by one and a half centimeters.We fix it with pins. There will be a drawstring for the elastic here.
• Using a sewing machine will help you make a cover for an office chair with your own hands. We use it to sew the product four millimeters from the edge, gradually removing the pins. Remember about the drawstring - when stitching, leave three centimeters along the edge of the hem.
• We stretch the elastic with a pin and pass it through the drawstring.
• Leave the end of the elastic at twenty centimeters after it has been passed through the entire product.
• We updated the office chair with our own hands, all that remains is to pull the ends of the elastic so that the cover fits tightly on the chair and tie it in a knot.

How to reupholster an office chair with your own hands

Before you reupholster an office chair with your own hands, you need to stock up on the necessary materials. These include:

• A piece of polyurethane foam with a density of 25. For the back, a material two centimeters thick is suitable; for comfortable sitting, it is better to choose three centimeters thick.
• Adhesive for polyurethane foam. It is important that the glue has no odor.
• Self-tapping screws and staples for wood.
• Sintepon.
• Microfiber of any shade.

To upholster a computer chair, you will need the following tool:

• Crosshead screwdriver. It is needed to remove seats and backs from chairs with metal frames.
• Manual air pistol.
• Sharp knife.
• Glue sprayer.

How to reupholster an office chair:

1. Unscrew the back using a screwdriver.
2. Remove the plastic attachments installed at the bottom.
3. Remove the backrest.
4. Get rid of old upholstery.
5. Cover the surface with spray glue.
6. Glue polyurethane foam.
7. Cut the foam along the contour of the seat.
8. Cut a piece of material to the required size.
9. To reupholster an office chair, you need to upholster all parts of the chair with new fabric.

How to sew a cover for an office chair

Sewing a cover for a computer chair with your own hands is not at all difficult. Regardless of the size and manufacturer, we use standard materials:

• Sewing machine, thread;
• Plastic film, tracing paper or graph paper;
• Snake or elastic band;
• Chalk, felt-tip pen, pencil;
• Scissors, ruler, set of pins;
• About one and a half meters of durable fabric.

You can sew a cover for a computer chair using a pattern you made yourself. We take polyethylene - a meter or one and a half, and apply it to the seat. Carefully straighten, secure and outline the contours of the seat. This will be the finished pattern of the cover. Sequence of work:

1. We cut out the material. To do this, lay the fabric on the table or floor, smooth it out, and remove the folds. We will attach the pattern to the material. We outline the contours of the parts, taking into account an allowance of four centimeters.
2. Cut out the parts from the fabric, rounding the corners parallel.
3. If there are many parts of the chair, for example, the back, sides, seat, it is better to number them so as not to get confused during the work process.
4. The middle inner part is sewn to the side section.
5. We try the cover on the seat. It should fit the furniture quite tightly. Problem areas where the fabric does not lie are corrected with darts.
6. We bend the material on both sides.
7. The workpiece must be stitched with a machine before combining the parts.
8. We make a straight line, cut off the remaining allowances, leaving five millimeters.
9. We monitor the symmetry of the seams.
10. Using this principle, we make the outer part of the back and sides. We sew in a snake.
11. We connect all the components and put the cover on the chair.
12. We make the side seams. The last fitting remains. We distribute the material around the perimeter of the seat, securing the places where darts will be needed.
13. We sew up the darts and sew the product completely.